UNABLE TO LOAD RESOURCE FILE 1003 CLAW ISO

DEBUG: db.c:376 db_get_common: Unable to find key вЂ1003/novmpwвЂ™ in family вЂAMPUSERвЂ™ DEBUG: db.c:376 db_get_common: Unable to find key вЂ1003/dialoptsвЂ™ in family вЂAMPUSERвЂ™ DEBUG: db.c:376 db_get_common: Unable to find key вЂ1003/pinlessвЂ™ in family вЂAMPUSERвЂ™ DEBUG: db.c:376 db_get_common: Unable to find key вЂ1003/screenвЂ™ in family вЂAMPUSERвЂ™ Some documentation IвЂ™m reading however states the Identity should be showing an IP address / CIDR not вЂњ1003-identify/1003вЂќ as what it is.

I do see it listed in pjsip show endpoints as 1003/1003. Supported: replaces,join,sdp-anat,norefersub,resource-priority,extended-refer,X-cisco-callinfo,X-cisco-serviceuri,X-cisco-escapecodes,X-cisco-service-control,X-cisco-srtp-fallback,X-cisco-monrec,X-cisco-config,X-cisco-sis-6.0.0,X-cisco-xsi-8.5.1 I enabled the pjsip debugging, and it shows: I changed the XLM to a chan_SIP extension and rebooted the phone I realized I had the extension set as pjsip, so I changed the port in the XLM to 5060 but then it doesnвЂ™t show up in the freepbx*CLI at all. I didnвЂ™t have to set up any вЂњendpointвЂќ for the Aastra, IвЂ™m now researching that area inside the freePBX itself to see whatвЂ™s up with that. NOTICE: res_pjsip/pjsip_distributor.c:649 log_failed_request: Request вЂREGISTERвЂ™ from вЂ failed for вЂ10.0.0.206:50077вЂ™ (callid: - No matching endpoint found DEBUG: res_pjsip_endpoint_identifier_user.c:137 username_identify: Endpoint not found for From username вЂ1001вЂ™ domain вЂ10.0.0.20вЂ™ DEBUG: res_pjsip_endpoint_identifier_user.c:133 username_identify: Attempting identify by From username вЂ1001вЂ™ domain вЂ10.0.0.20вЂ™ DEBUG: res_pjsip_endpoint_identifier_ip.c:222 ip_identify: Identify checks by IP address failed to find match: вЂ10.0.0.206:50077вЂ™ did not match any identify section rules I see it trying to register, but it seems to be failing here: The Aastra 6755i phone is registered using chan_pjsip, but the Cisco 7942 is still sitting at вЂњRegisteringвЂќ.

UNABLE TO LOAD RESOURCE FILE 1003 CLAW ISO

I also just noticed the timezone was off (even though I set it during the initial ISO config) so thatвЂ™s been fixed now. Other than it being вЂњnew technology / newer protocolвЂќ, is there a specific reason to have the pjsip enabled? IвЂ™m contemplating disabling it, and changing the chan_sip to 5060вЂ¦ Looking in the /etc/asterisk/ there is no pjsip_nf. ERROR res_sorcery_config.c: Could not create an object of type вЂtransportвЂ™ with id вЂ10.0.0.20-tcpвЂ™ from configuration file вЂnfвЂ™ДЎ0.0.0.20 is the IP of my freePBX server. ERROR res_pjsip/config_transport.c: Transport вЂ10.0.0.20-tcpвЂ™ could not be started: Address already in use ERROR res_sorcery_config.c: Could not create an object of type вЂtransportвЂ™ with id вЂ127.0.0.1-tcpвЂ™ from configuration file вЂnfвЂ™ ERROR res_pjsip/config_transport.c: Transport вЂ127.0.0.1-tcpвЂ™ could not be started: Address already in use

ERROR res_sorcery_config.c: Could not create an object of type вЂtransportвЂ™ with id вЂ10.0.0.20-udpвЂ™ from configuration file вЂnfвЂ™ ERROR res_pjsip/config_transport.c: Transport вЂ10.0.0.20-udpвЂ™ could not be started: Address already in use ERROR res_sorcery_config.c: Could not create an object of type вЂtransportвЂ™ with id вЂ127.0.0.1-udpвЂ™ from configuration file вЂnfвЂ™ ERROR res_pjsip/config_transport.c: Transport вЂ127.0.0.1-udpвЂ™ could not be started: Address already in use VERBOSE config.c: Parsing вЂ/etc/asterisk/pjsip_custom_nfвЂ™: Found ERROR res_pjsip_config_wizard.c: Unable to load config file вЂpjsip_nfвЂ™ The Cisco phones are not registering, and IвЂ™m seeing lines in the logs:

Unable to load resource file 1003 claw